片语

Set UART设定通用异步传输器

UART timing串口授时

uart driver串行驱动程序

software UART软件UART

UART ContrllerUART控制器

Uart Instance异步例如

et UART设定通用异步传输器

enhanced uart增强型uart

uart data异步数据

英汉例句

• Consider a handheld with a built-in CSR Bluetooth chipset interfaced to the system using a UART interface.

  考虑一种拥有内置CSRBluetooth芯片组的手持设备与使用UART接口的系统的连接。

• Packet indicator (for UART interfaces) of 3.

  数据包指示符(对uart接口而言)为3。

• Scroll to your UART「s line, and enter 0xa0000000 in the Base address field (this was the default address for the 16550 UART you just deleted, so you know it」s a safe place to put the lite UART).

  滚动到uart行，在BaseAddress字段中输入0xa0000000(这是刚删除的16550UART的默认地址，因此可知这是存储小uart的安全位置)。

• Packet indicator (for UART interfaces) of 2.

  数据包指示符(对uart接口而言)为2。

• Packet indicator (for UART interfaces) of 4.

  数据包指示符（对UART接口而言）为4

• In the hardware field, CPLD is entitled for system logical control; Serial communication derived from UART (Universal Asynchronous Receiver Transmitter) frees the DSP of burdensome control.

  在硬件上采用CPLD来完成系统的逻辑控制，利用UART(通用异步收发器)来进行串行通信，使DSP从繁忙的控制任务中解放出来。

• This paper presents a design of a simple UART IP core.

  文章主要介绍一种简易通用的UARTIP核的设计。

• Now you need to define where the UART lives in the PowerPC「s address space; do this on the Addresses TAB, as shown in Figure 4.

  现在需要定义UART在PowerPC地址空间中的位置；在Addresses选项卡上执行此操作，如图4所示。

• The second section, the principle of UART and IRDA1.0 protocol is analyzed deeply.

  第二章，详细介绍了UART的工作原理和相关的红外通讯协议。

• Packet indicator (for UART interfaces) of 1.

  数据包指示符（对UART接口而言）为1

• In the Size drop-down list, select the smallest value (256) — the lite UART actually has only four 32-bit registers, and hence only requires 16 bytes of address space, so 256 bytes is plenty.

  在size下拉列表中，选择最小值(256)——小uart实际上只有4个32位寄存器，因此只需要16字节的地址空间，所以256个字节绰绰有余。

• Most IrDa chips in the SIR mode are UART 16650-compatible (16650 is a common PC UART), so the legacy Linux serial port drivers can serve as link-level drivers.

  大多数处于SIR模式的IrDa芯片是UART 16650兼容的（16650是一种公共PCUART），因此传统Linux串口驱动程序可以充当链路级别的驱动程序。

• This is what I did do a UART transmitter when the source and hope for all of us.

  这是我做UART时候做的一个发送器的源码，希望对大家有用。

• This article introduces particularly the UART work elements of ARM and the connect method directly between ARM and the PC serial interface.

  详细介绍了ARM自带的UART的工作原理及与计算机串行口的连接方法。

• You can live without Ethernet and IIC, but the UART is really vital for debugging, if nothing else; you need to fix this.

  可以没有以太网和IIC，但是UART对于调试来说是必需的。所以需要修正这个问题。

• The problem with your UART baudrate may be clock related.

  您的UART波特率问题可能是系统时钟造成的。

• The legacy serial driver that drives this board」s UART channels can send and receive data from the BlueZ UART transport driver.

  这个母板的UART通道使用的传统串行驱动程序可以从BlueZUART传输驱动程序上收发数据。

• This can be implemented as a hardware facility or UART relieving processor(and applications programmer) of this low-level, time-consuming, detail.

  这种工作可以使用硬件或者UART来实现，可以将处理器或者应用程序从这种底层的、费时的和琐碎的工作解脱出来。

• UART allow to full-duplex communication at serial link circuit.

  UART允许在串行链路上进行全双工的通信。

• While H4 serves as the standard method to transmit Bluetooth data over UART as defined in the specifications, the proprietary BCSP protocol from CSR supports error checking and retransmission.

  而H4充当通过UART传输Bluetooth数据的标準方法。UART是在规范中定义的来自CSR的专有BCSP协议，支持错误校验和重传。